AIRLESSCO 910E Manuel d'instructions télécharger pdf (Page 5)

WARNINGS - CONTINUED

Hazardous uid or toxic fumes can cause serious injury or

death if splashed in eyes or on skin, inhaled or swallowed.

Know the hazards of the uid you are using. Store &

dispose of hazardous uids according to manufacturer,

local, state & national guidelines.

ALWAYS wear protective eyewear, gloves, clothing

and respirator as recommended by uid manufacturer.

Keep all labels on the unit clean and readable.

Replacement labels are available from manufacturer.

Tighten all uid connections securely before each use. High

pressure uid can dislodge a loose coupling or allow high

pressure spray to be emitted from the coupling and result in

an injection injury or serious bodily injury.

Use only hose that has a spring guard. The spring guard

helps protect the hose from kinks or other damage which

could result in hose rupture and cause an injection injury.

NEVER use a damaged hose, which can result in hose

failure or rupture and cause in injection injury or other

serious bodily injury or bodily damage. Before each use,

check entire hose for cuts, leaks, abrasion or bulging of

cover, or damage or movement of couplings. If any of

these conditions exist, replace the hose immediately.

Never use tape or any device to try to mend the hose as it

cannot contain the high pressure uid. NEVER ATTEMPT

TO RECOUPLE THE HOSE. High pressure hose is not

recoupleable.

Help prevent damage to the hose by handling and routing

it carefully. Do not move the sprayer by pulling it with the

hose.

Ground the sprayer and other components in the system

to reduce the risk of static sparking, re or explosion which

can result in serious bodily injury and property damage.

ALWAYS GROUND ALL OF THESE COMPONENTS:

1. Sprayer: Connect a ground wire and clamp (supplied) to

a true earth ground.

2. Fluid Hose: use only grounded hoses.

3. Spray gun or dispensing valve: grounding is obtained

through connection to a properly grounded uid hose

and pump.

4. Object being sprayed: according to your local code.

5. All solvent pails used when ushing should only be

metal pails which are conductive.

Once each week, check electrical resistance of hose (when

using multiple hose assemblies, check overall resistance of

unpressurized hose must not exceed 29 megohms (max)

for any coupled length or combination of hose lengths. If

hose exceeds these limits, replace it immediately.

Never exceed 500 Ft. (150 m.) overall combined hose

length to assure electrical continuity.

Keep clear of moving parts when starting or operating

the sprayer. Do not put your ngers into any openings

to avoid amputation by moving parts or burns on hot

parts.Precaution is the best insurance against an

accident.

When starting the engine, maintain a safe distance

from moving parts of the equipment.

Before adjusting or servicing any mechanical part

of the sprayer, follow the PRESSURE RELIEF

PROCEDURE on page 8, and remove the ignition

cable from the spark plug to prevent accidental

starting of sprayer.

TOXIC FLUID HAZARD

WARNINGS CONTINUED ON NEXT PAGE.........

LABELING

HOSES

KEEP CLEAR OF MOVING PARTS

GROUNDING

UL RECOMENDATION FOR MINIMUM GAUGE EXTENSION CORD

AMPERAGE

RATING

RANGE

VOLTAGE LENGTH OF CORD IN FEET

25 50 100 150 200 250 300 400 500

5-6 120 18 16 12 12 10 10 8 8 6

6-8 120 18 16 12 10 10 8 6 6 6

8-10 120 18 14 12 10 8 8 6 6 4

10-12 120 16 14 10 8 8 6 6 4 4

1 2 3 4 5 6 7 8 9 10 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

AIRLESSCO 910E Manuel d'instructions Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Pulvérisateur de peinture AIRLESSCO 910E