AIRLESSCO 3A1182B Manuel d'instructions

3A1182BENOperation/Repair/PartsAirless Paint SprayerFor application of architectural paints and coatings.Airlessco - EZ Rent 570 Hi Boy (24F585), EZ R

Operation 10 3A1182BAdjusting the PressureWhen adjusting the pressure, turn the Pressure Control Knob clockwise to increase pressure and counterclock-

Maintenance3A1182B 11MaintenanceDaily MaintenanceKeep displacement pump packing nut/wet cup 1/3 full of Airlessco Throat Seal Oil at all times. The TS

Maintenance 12 3A1182BFluid Pump Reinstall1. Loosen the packing nut and ensure the piston rod (10) is in its upper position in the fluid pump body (9)

Maintenance3A1182B 13Packing Replacement ProceduresDisassembly of the Fluid Pump1. Disconnect the Fluid Pump, page 11.2. Unscrew and remove the packin

Maintenance 14 3A1182B18. Reinstall Fluid Pump, page 12.Gear and Pump AssemblyServicing Gear box Assembly1. Remove fluid pump. See Fluid Pump Disconne

Maintenance3A1182B 15Replacement of Electrical ComponentsNOTE: Anytime the pressure control assembly, sensor, or both are replaced, perform the calibr

Troubleshooting 16 3A1182BTroubleshootingGeneralProblem Cause SolutionUnit doesn’t prime Airleak due to loose suction nut Tighten suction nut.Airleak

Troubleshooting3A1182B 17Machine does not start Motor Remove the motor brush covers and turn the machine ON. Set the potentiometer (POT) at maximum pr

Troubleshooting 18 3A1182BPressure Control RepairMotor Control Board DiagnosticsNOTE: Keep a new transducer on hand to use for test.1. For sprayers wi

Troubleshooting3A1182B 19Digital Display MessagesNo display does not mean that spayer is not pressurized. Relieve pressure before repair. See Pressure

Warnings 2 3A1182BWarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-tion point

Troubleshooting 20 3A1182BAirless Spray GunProblem Cause SolutionCoarse spray Low pressure Increase the pressureExcessive fogging (overspray) High pre

Troubleshooting3A1182B 21Servicing the Inlet Valve1. Un-thread and remove suction nut from the fluid pump body (8).2. Remove suction seat (12), O-ring

Parts 22 3A1182BPartsManifold Filter (866480)12345967107Ref. Part Description Qty.1 867145 COVER 12 301356 SPRING 13 867377 O-RING 14 867214 FILTER 60

Parts3A1182B 23Lo-Boy Frame Parts Diagram121361311241291271285130677877Ref. Part Description Qty.1 331491 MOTOR 12 331171 FRAME 15 867736 WHEEL 26 143

Parts 24 3A1182BHi-Boy Frame Parts Diagram12346778775ti17439aRef. Part Description Qty.1 331491 MOTOR 12 331273 FRAME 13 16F551 FASTENER,THREAD,EXTERN

Parts3A1182B 25Control Parts Diagram99510319272122202310110297339292769696982511030342610094ti17482aRef. Part Description Qty.9 867800 TERMINAL BOX WE

Parts 26 3A1182BMotor and Drive Parts Diagram421562133113112813536373940414344454647474848495155565758596061626368686466697071910181811141616173272153

Parts3A1182B 27▲ Additional warning labels are available at no cost.Ref. Part Description Qty.1 331491 MOTOR 11a 331785 FAN (not shown) 11b 331786 FAN

Parts 28 3A1182BPacking Replacement6*7*271112*13*15*42114261*1*3*23*23*2*2*2*24*25*16*16*16*2017*19*22*18*5ti16057a

Parts3A1182B 29Packing ReplacementRef. Part Description Qty.1* 331014 MALE GLAND 22* 331016 PACKING POLYETHYLENE 63* 331308 FEMALE ADAPTOR 14 331011 F

Warnings3A1182B 3WARNINGWARNINGWARNINGWARNINGFIRE AND EXPLOSION HAZARDFlammable fumes, such as solvent and paint fumes, in work area can ignite or exp

Parts 30 3A1182BGearbox Sleeve Bearing ReplacementSuction AssembliesNOTE: When replacing item (1), cover outside of sleeve with 6 drops of Loctite 246

Parts3A1182B 31Electrical System - EZ SeriesON/OFF SwitchPower Plugfrom MotorBlack (+)WhiteBlack Green2 x RedBlack (-)Black Black ti2471b13567Ref.Part

Parts 32 3A1182BElectrical Componentsti16066a1234567Ref. Part Description Qty. Ref. Part Description Qty.1* 867816 SCREW 2 4* 117281 SPACER 22 867804

Parts3A1182B 33EZ Series Electric Paint Sprayer Quick Reference GuideOperationPrime Pressure Relief Valve (Prime-PR Valve)Used to relieve pressure fro

Parts 34 3A1182BCleaning• Always use low pressure in the cleaning process.• Always remove spray tip before cleaning - AFTER following the Pressure Rel

Technical Data3A1182B 35Technical DataPower requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100V AC, 50 hz, 11

TO PLACE AN ORDER OR FOR SERVICE, contact your Airlessco distributor, or call 1–800–223-8213 to identify the nearest distributor.All written and visua

Warnings 4 3A1182BSKIN INJECTION HAZARDDo not aim the gun at, or spray any person or animal.• Keep hands and other body parts away from the discharge.

Warnings3A1182B 5MOVING PARTS HAZARDMoving parts can pinch, cut or amputate fingers and other body parts.• Keep clear of moving parts.• Do not operate

Component Identification 6 3A1182BComponent IdentificationEDCABti17301aA Power switch Turns sprayer ON and OFFB Pressure Control Knob Adjusts pressure

Operation3A1182B 7OperationPressure Relief Procedure1. Engage the gun trigger lock. Refer to the separate instruction manual provided with gun for saf

Operation 8 3A1182BFill the Packing Nut/Wet Cup1. Fill the Packing Nut/Wet Cup with 5 drops of Air-lessco Throat Seal Oil (TSO).Flush the Sprayer1. Fl

Operation3A1182B 96. Turn the engine ON/OFF switch to ON.7. Point the gun into the metal pail and hold a metal part of the gun firmly against the pail