AIRLESSCO 1110E Manuel d'instructions Page 1

3A1184AENGOperation/Repair/PartsAirless Paint SprayerFor application of architectural paints and coatings. For professional use only.Airlessco - SL110

Operation 10 3A1184AShutdown1. Relieve Pressure, page 7.2. Clean the tip and gun as recommended in the sepa-rate Gun Manual supplied with the gun.3. I

Maintenance3A1184A 11MaintenanceRegular Maintenance1. Always stop the pump at the bottom of its stroke when you take a break or at the end of the day.

Maintenance 12 3A1184AReplacement of Belt/Belt AdjustmentNOTE: The Cog Belt System does not require align-ment. When upper sheave is placed on motor s

Maintenance3A1184A 13Fluid Pump Reinstall1. Loosen the packing nut and extend piston rod to fully up position. Slip sleeve over the piston rod.2. Inse

Maintenance 14 3A1184AServicing Inlet Nut and Outlet ValveInlet Valve1. Using the rod collar tool (865008), unscrew the suc-tion nut (6), containing s

Maintenance3A1184A 15Packing Replacement ProceduresDisassembly of the Fluid Pump1. Unscrew and remove the packing nut (2).2. Push the piston rod (1) d

Maintenance 16 3A1184A17. Thread the packing nut (2) into the top of the fluid body (3) and tighten hand tight.18. Take the suction retainer (10) and

Maintenance3A1184A 17Pressure Control Assembly CalibrationNOTE: Anytime a sensor or pressure control assembly (board) or both are replaced, the follow

Maintenance 18 3A1184APhase Limit CalibrationFormerly known as the low voltage or master voltage calibration.1. Attach a 50’, 1/4” airless hose, airle

Maintenance3A1184A 19Liquid Crystal Display (LCD)1. Ensure the power switch is OFF and the machine is unplugged. 2. Detach the pressure control assemb

Warnings 2 3A1184AWarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-tion point

Troubleshooting 20 3A1184ATroubleshootingGeneralProblem Cause SolutionUnit doesn’t prime Airleak due to loose suction nut Tighten suction nut.Airleak

Troubleshooting3A1184A 21Power Source Using a Phillips Head screwdriver, remove the eight screws holding the pressure control assembly. Locate the red

Troubleshooting 22 3A1184ASensor Plug another sensor board into the board and perform the zero calibration procedure. If the machine starts to run, th

Troubleshooting3A1184A 23Thin distribution in center of pattern “horns”Worn tip Change to new tipWrong tip Use tip with narrow spray angleThick skin o

Parts 24 3A1184APartsPaint System12345678910111213141516172019181112ti16145aRef. Part Description Qty. Ref. Part Description Qty.1 866428 Prime Valve

Parts3A1184A 25Manifold Filter (865627)Ref. Part Description Qty. Ref. Part Description Qty.1 867145 Base 1 6 867077 Base 12 301356 Spring 1 7 867004

Parts 26 3A1184AFluid Pump123456789101112131415166ti16033aRef. Part Description Qty.1 866143 Gearbox 1” (1100/1110E) 12 301320 Cover 13 867529 Screw 1

Parts3A1184A 27Inlet and Outlet ValvesRef. Part Description Qty.1 867051 Ball 12 556562 O-Ring 13 867574 Suction Seat 14 866306 Retainer 15 866400 Sup

Parts 28 3A1184AComplete Sprayerti16146a1345565758285529303132333549425051275253546789101113141617181920172122232425262736, 37, 38,39, 414546474843443

Parts3A1184A 29▲ Additional warning labels are available at no cost.Ref. Part Description Qty. Ref. Part Description Qty.1 301320 Cover 1 35 342425▲ H

Warnings3A1184A 3WARNINGWARNINGWARNINGWARNINGFIRE AND EXPLOSION HAZARDFlammable fumes, such as solvent and paint fumes, in work area can ignite or exp

Parts 30 3A1184APacking Replacement1221941718171615162021232345678910111213141516171815171619202122232425261ti16001ati16002aRef. Part Description Qty.

Parts3A1184A 31Suction AssembliesTO FLUID PUMPRef. Part Description Qty.1 301594 Suction Assembly 12 187090 Inlet Strainer 13* 241920 Threaded Deflect

Parts 32 3A1184AElectrical System S1 S2 A2 A1 L1 L2 INHIBIT SWITCH P-ZR ON-SL DISPLAY SENSOR POTGREENBLACKBLACKREDREDBLACK/BROWNBLK LCD ZERO PRESSURE

Parts3A1184A 33Electrical Components123456ti16149aRef. Part Description Qty. Ref. Part Description Qty.1 867327 Nut 4 5 331360 Window 12 867760 Plasti

Technical Data 34 3A1184ATechnical DataPower requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120V AC, 60 hz,

Notes3A1184A 35Notes

TO PLACE AN ORDER OR FOR SERVICE, contact your Airlessco distributor, or call 1–800–223-8213 to identify the nearest distributor.All written and visua

Warnings 4 3A1184ASKIN INJECTION HAZARDHigh-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that i

Warnings3A1184A 5MOVING PARTS HAZARDMoving parts can pinch, cut or amputate fingers and other body parts.• Keep clear of moving parts.• Do not operate

Component Identification 6 3A1184AComponent Identificationti14791ati14790aEFti16142aABCDA Power switch Turns sprayer ON and OFFBFuse 20 AMPC Pressure

Operation3A1184A 7OperationPressure Relief Procedure1. Engage the gun trigger lock. Refer to the separate instruction manual provided with gun for saf

Operation 8 3A1184AFill the Packing Nut/Wet Cup1. Fill the Packing Nut/Wet Cup with 5 drops of Air-lessco Throat Seal Oil (TSO).Flush the Sprayer1. Fl

Operation3A1184A 97. Point the gun into the metal pail and hold a metal part of the gun firmly against the pail. Maintain firm metal to metal contact